The post 23-301A0-R – Switch connector appeared first on RFMW UK, Ltd..

Product Detail

• Impedance: 50 Ohms
• Configuration: 4 Attenuators (Solid-State)
• 95 dB Total
• 1 dB Step
• Frequency Start: 200 MHz
• Frequency Stop: 6 GHz
• Control: Manual / Ethernet / RS-232

The post 50BA-011-63 – Programmable Attenuator appeared first on RFMW UK, Ltd..

The 50FHIE is capable of handling 1000 watts of RF power with no liquid cooling or forced-air requirements. Operating frequency range is DC to 3 GHz and the attenuators are available with N connectors in values of 10 dB, 20 dB, or 30 dB.

Product Details

• Frequency: DC – 3000 MHz
• RF Input Power: 1000 Watts, uni-directional
• Attenuation Values: 20, 30, 40 dB
• Heatsink Style: Square
• RF Connectors: N, 7/16

The post 50FHIE – High Power Attenuator appeared first on RFMW UK, Ltd..

Product Details

• 95 dB Total
• 1 dB Step
• Frequency Start: 200 MHz
• Frequency Stop: 6 GHz
• 1 uS Switching Speed
• RF Input Power: +20 dBm
• USB Control
• RF Connectors: SMA

The post 50P-2014 – Variable Attenuator appeared first on RFMW UK, Ltd..

The post 885136 – Band pass filter appeared first on RFMW UK, Ltd..

When you need a high frequency Hi-Rel reference clock, this industry standard DOC203810, Rev D standard specification is the answer. Revision D boasts an expanded upper frequency limit from 500MHz to 700MHz including a maximum bandwidth jitter performance of 0.3ps rms over 12kHz to 20MHz. Additional features include a dual complementary output pairs option (1308/1340) and leadforming option for all platforms. Using DOC203810 will significantly reduce design time and overall project costs.

Features include:

• Dual complementary output pairs option
• Expanded upper frequency limit from 500MHz to 700MHz
• Includes maximum jitter performance
• Addition of leadforming options with recommended pad layouts
• Enhanced electrical performance table
• Addition of NASA INST-EEE-002 compliance comparisons
• Shorter leadtimes for TOR-level (Enhanced Element Evaluation) requirements
• Improved comprehensive outline drawings

Click here for datasheet

The post DOC203810 – Hi-Rel LVPECL Clock Oscillators appeared first on RFMW UK, Ltd..

The post IMS1141-10DB – IMS Attenuator appeared first on RFMW UK, Ltd..

The post JN040 – Trimmer capacitor appeared first on RFMW UK, Ltd..

The MINI-POLE® is optimized for size, RF power handling, low distortion, and exceptional selectivity. The MINI-POLE® comes in a compact 42  in DIP package 0.558 x 1.305 x 2.250 inches (14.17 x 33.15 x 57.15 mm.)

The MINI-POLE® uses a high factor pin diode switched capacitor array with a customized high voltage driver to accurately and reliably tune to pre-defined frequencies. The MINI-POLE® is primarily used in applications where adjacent radio channels may cause interference on the acquisition channel. The MINI-POLE® can be  used to reduce or eliminate the effects of these interfering signals but it is flexible enough to be used in a multitude of applications.

The MINI-POLE® uses an 8-bit wide proprietary parallel or serial interface to tune to a maximum of 251 tune positions per band. The MINI-POLE® will typically tune in less than 10 μs. The MINI-POLE® requires only two external power supplies, +5V and +100V.

All MINI-POLE® filters are fully aligned and tested by POLE/ZERO® for convenience and ease of use. The MINI-POLE® covers six frequency ranges and custom configurations and designs are available upon request.

Typical Applications

• Applications where small size, high power, and high performance are required
• Military Radios
• Military Radar
• SATCOM
• Test and Measurement Equipment
• Industrial and Medical Equipment

Features

• Up to +30 dBm CW continuous in-band power handling
• Up to +37 dBm CW continuous out-of-band power handling
• +40 dBm IIP3 typical
• 10 μs typical tune time
• Up to 70 dB typical ultimate selectivity at (2 x 𝑓𝑐)

Datasheet

MN-X-X-X-T01 (Mini-Pole) Datasheet

The post MN-X-X-X-T01, 30–520MHz, 1W, Tunable Bandpass Filter Series appeared first on RFMW UK, Ltd..

Click for data sheet 

The post QPA2363C – SiGe Gain Blocks appeared first on RFMW UK, Ltd..